Mobile power car diesel generator set

The mobile power car is composed of a second-class car chassis, a silent cabin, a diesel engine, a generator set, a control system, internal and external lighting devices, power transmission and distribution devices, cable reels, power input, output interfaces, hydraulic legs and so on.

Car detailed parameters:

The cabin adopts mute box body, and the sound insulation material of the box body adopts flame retardant fireproof and environmental protection products.

The inner wall of the box must be made of metal plates, professional-grade metal sound-absorbing Boeing plates.

Double sealed maintenance doors on both sides of the generator in the middle of the car, and there is a maintenance step invisible under the door

The cooling water tank of the generator set is facing the front of the car for easy heat dissipation. An independent sound-absorbing exhaust bin is set up in the front section of the vehicle volume, and all aluminum alloy shutters are installed.

Silent standard: average measurement at 1 meter≤75db

The vehicle support system uses 4-point hydraulic support, and the single-leg support force is greater than 8 tons.

Genset parameters:

Diesel engine: Cummins, Volvo, Mitsubishi, MAN, Shangchai, Yuchai, Weichai and other well-known domestic and foreign brands can be used as configuration parameters.

Generator: Stanford STAMFORD motor, marathon, Inger, Audi, Leroy Somer, Shuangma, etc. can be selected as configuration parameters.

Control module: the configuration parameters can be selected from Chinese deep-sea, Komai, Zhongzhi, Kaixun and other Chinese LCD digital displays

The main power 50-500KW diesel generator set,

Rated voltage 400/230V, rated frequency 50HZ,

Connection mode: three-phase four-wire connection,

Protection grade IP23,

Voltage steady state adjustment rate (≤%±3)

Voltage transient adjustment rate (≤%) 20 ~-15,

Voltage stabilization time (S) ≤3,

Excitation mode: Brushless self-excitation copper core motor,

Speed regulation method: electronic automatic speed regulation;

Pressure regulation system: automatic pressure regulation;

Start mode: DC 24V electric start;

Start and stop mode: manual/automatic.

Display function: display various parameters of the generator set, such as generator speed, oil pressure, engine cooling water temperature, engine operating time, battery voltage, unit three-phase voltage, three-phase current, frequency, automatic/manual/disconnect function selection switch , Mains battery charger, emergency stop switch; with high water temperature, low water level, low oil pressure, overspeed, vulgar, short circuit overcurrent, high voltage, low voltage, charging failure and other alarm functions. Support 14 languages, and the display content can be edited (including Chinese)

Alarm classification: pre-alarm, electrical trip and shutdown, manual control of fuel pump, manual control of engine speed (EFI engine)

• Presetable operation time (the unit needs to be started regularly for maintenance operation) • Presetable maintenance cycle function (engine running 250 hours, need to change three filters, etc.) • Software firmware version can be upgraded by itself (for example: upgrade from version 3.0 to Version 5.0) • With engine and generator monitoring and protection functions-engine speed, engine oil pressure, engine water temperature, battery voltage, generator voltage-generator current, engine frequency • Both RS232 and RS485 communication ports are supported • Modbus RTU is supported Communication protocol • With PLC logic function (supports 50 steps) • Sleep power-saving mode • Hierarchical load dumping-loading / hierarchical plus virtual load (load box) • If you do not need to detect the mains, you can set to disable the mains detection function • Can be canceled All protection functions • 250 event records (with date and time)

Supporting output of power car: (optional)

Load output cable ZRYCW130 type oil-resistant flame-retardant flexible cable, two for each phase of A, B, and C, and a zero line for a total of 400 meters. The load cable winch is hydraulically driven and can be operated manually/automatically, capable of winding 50 meters of cable.

Load cable quick plug/seat 16BV, 8 plug/8 socket,.

The vehicle load output box is equipped with a copper bar with a common grounding point, and the load output copper bar insulation shield has a copper bar live indicator,

Quick plugs/seats for power output for distribution unit maintenance: one set of three-phase 400V/32A, one set of single-phase 230V/32A, one set of single-phase six-hole socket 230V/10A;

Equipped with mains single-phase input quick plug/seat: single-phase 230V/32A set; all sockets are equipped with corresponding current circuit breakers.